Okin JLDQ.10.371.183A Recliner Actuator

How to Replace an Okin JLDQ.10.371.183A Recliner Motor

Replacing a faulty Okin Refined electric recliner actuator can be a straightforward DIY repair for someone comfortable working with basic tools. This guide explains how to remove an existing JLDQ.10.371.183A actuator and install the newer JLDQ.19.371.183Z01 replacement supplied by Sofa Rehab.

Important: The replacement motor will be labelled JLDQ.19.371.183Z01. This is the newer compatible model and is the correct actuator supplied when ordering a replacement for the older JLDQ.10.371.183A.

Step 1: Disconnect the Recliner from Power

Switch off the recliner at the wall socket and unplug its power supply before starting any work. Disconnect any battery backup if fitted.

Position the recliner so you can safely access the underside. Depending on the furniture design, this may involve carefully tilting the chair or lounge backwards. Have another person assist if necessary, and protect the floor and upholstery from damage.

Safety: Recliner mechanisms contain moving parts and potential pinch points. Ensure the mechanism is stable and properly supported before removing any mounting pins or bolts. Never place your hands between unsupported moving components.

Step 2: Locate and Identify the Existing Actuator

Locate the electric recliner motor attached to the reclining mechanism underneath the furniture. The actuator will generally be secured at two mounting points and connected to the electrical system by a power cable.

Check the identification label on your original actuator. The JLDQ.19.371.183Z01 is a replacement for the following Okin models:

• JLDQ.10.371.183A

Some reclining furniture uses more than one actuator. The JLDQ.10.371.183A is commonly paired with the JLDQ.10.413.177A or JLDQ.19.413.177F03, which is a different motor. Make sure you have identified the actuator that requires replacement before proceeding.

Step 3: Disconnect the Power Cable

Follow the cable from the existing actuator to its connection point and carefully disconnect the 3 plugs.

Hold the connector housing when disconnecting it rather than pulling on the wires. Release any locking mechanism if fitted, and note how the cables are routed around the recliner frame.

Check for cable clips or ties that may need to be removed to free the existing actuator.

Step 4: Remove the Existing Recliner Motor

Before removing the actuator, support the reclining mechanism so it cannot move unexpectedly. The mechanism may be under load, even when the power is disconnected.

Locate the mounting pins, retaining clips or bolts securing the actuator at each end. Carefully remove the retaining hardware, keeping any reusable parts in a safe location.

Once both mounting points are released and the mechanism is safely supported, carefully remove the existing actuator from the furniture.

Note: The Sofa Rehab replacement actuator does not include mounting pins, clips or additional hardware. Existing mounting components may be reused if they are in good condition and suitable for the replacement.

Step 5: Compare the Old and New Actuators

Place the original actuator beside the replacement JLDQ.19.371.183Z01 and compare the following features:

• Overall actuator design and mounting arrangement.
• 371mm installation length between mounting centres when retracted.
• 183mm actuator stroke.
• Mounting hole positions and suitability of the existing hardware.
• 1x 2-pin male power plug, 1 x 2-pin female actuator plug and 1x 5-pin female DIN plug and clasp.

The replacement motor may have a different model number printed on its label. This is expected, as the newer JLDQ.19.371.183Z01 replaces the original JLDQ.10.371.183A actuators.

Important: Do not force the replacement into position or operate the actuator to adjust its length while it is unsecured. If the mounting points do not align, stop and check the mechanism position and actuator compatibility before proceeding.

Step 6: Install the Replacement Actuator

Position the new Okin JLDQ.19.371.183Z01 actuator in the same orientation as the original motor, ensuring the mounting points align correctly with the recliner mechanism.

With the mechanism safely supported, secure the actuator using the appropriate mounting pins, retaining clips or bolts. Confirm that all retaining hardware is correctly fitted and that the actuator is securely mounted at both ends.

Ensure the actuator body and moving rod have sufficient clearance from surrounding components throughout the recliner’s intended movement.

Step 7: Reconnect the Plugs

Reconnect the replacement actuator’s plug’s to the corresponding connector’s in the recliner’s electrical system.

Ensure the connector’s are fully seated and route the cable away from moving mechanisms, sharp edges and areas where it could become pinched or stretched.

Secure any loose wiring using suitable cable restraints where necessary, without placing tension on the electrical connection.

Step 8: Test the Recliner Operation

Once the actuator is fully mounted, all tools have been removed and the mechanism is clear of obstructions, return the furniture to its normal operating position.

Reconnect the power supply and carefully operate the recliner using its existing control switch or handset.

Observe the reclining mechanism as it moves, checking that:

• The recliner moves smoothly in the intended direction.
• The actuator remains securely mounted.
• There are no unusual noises, binding or obstructions.
• The power cable remains clear of moving components.
• The recliner operates correctly through its normal range of movement.

If the mechanism binds, makes unusual noises or does not operate correctly, stop immediately, disconnect the power and investigate the issue before further operation.

Avoid repeatedly operating the motor without allowing it to cool. Follow the operating duty cycle and electrical ratings specified on the replacement actuator.

Need Help Replacing Your Okin Recliner Motor?

At Sofa Rehab, we specialise in replacement electric recliner motors and DIY furniture repair parts. If you are unsure whether the JLDQ.19.371.183Z01 is the correct replacement, contact us with photos of your original actuator, its model number and the electrical connection.

We can help you identify the appropriate replacement so you can get your electric recliner working again.