Accessories, Electric Recliner Spare Parts, Leads/Plugs
Mulin Charging Station MLCZ005-13
$160.00
In stock
Flush-mount AU/NZ charging station with 'pop up' twin 240 V sockets and dual USB-A ports, the Mulin Electric MLCZ005-13 retro-fits neatly into powered recliners, theatre lounges and desks. Silver in colour and drops into a 220mm × 110mm cut-out, presents a 265mm × 120mm low-profile bezel, and arrives pre-wired with a 1.4m mains lead for plug-and-play DIY installation. Pop-Up Twin Power & USB Console Charger. Suitable for Synargy Smart Comfort, Amart and Harvey Norman lounges—as well as any furniture needing convenience power—this universal module secures with four screws and is ready to use in minutes, no special tools or skills required. Need Other Recliner Electronics or Help? Browse our full range of electric recliner accessories (click here) for cup holders, switches and power kits, or contact us for friendly expert advice finding the exact part you need. read more
In stock
- Description
- Technical Specifications
- How To
- Reviews (0)
- FAQs
- Add a review
Description
Pop-Up Twin Power & USB Charging Station – MLCZ005-13
Bring convenient laptop and device charging right to your seat. This flush-mount module drops into a standard 220 mm × 110 mm cut-out and presents a neat 265 mm × 120 mm bezel that sits almost flush with the arm-rest or console lid when closed. Inside you’ll find two Australian 240 V power outlets plus dual USB-A ports (5 V 2 A shared) – perfect for phones, tablets, or game controllers. A captive 1.4 m mains lead with a 3-pin AU plug means true plug-and-play installation.
Universal Retrofit for Synargy, Amart & Harvey Norman Lounges
The MLCZ005 family is factory-fitted in many Smart Comfort theatre groups and other powered sofas sold through Australia’s big retailers. Whether you’re replacing a faulty charger or adding one to an older lounge, this AU-specific “-13” version matches the original styling and wiring for a seamless swap.
Quality, Certified & Ready To Use from Sofa Rehab
- Two AS/NZS 3112 10 A outlets (250V).
- Two USB-A ports, 5 V 2 A shared.
- Satin-black bezel with brushed-steel pop-up lid.
- ERAC Level-3 safety approval for Australian use.
- Pre-wired 1.4 m mains cord – no electrician required.
You Can Do It — DIY Installation in Minutes
Replacing a faulty bed actuator is a straightforward DIY task: unplug the bed, remove two axel covers, swap the drive, and reconnect the handset and mains lead – typically a ten-minute job. Follow our step-by-step guide in the “How To Tutorial” tab to get your adjustable bed working again today. Enjoy the satisfaction of a job well done and the savings from avoiding an in-home service call!
Technical Specifications
Technical Specifications
Technical Specifications
| Model / SKU | MLCZ005-13 (AU) |
|---|---|
| Input | 240–250 V AC · 50 Hz · 10 A max |
| AC Outputs | 2 × AS/NZS 3112 Type-I sockets (250 V 10 A each) |
| USB Outputs | 2 × USB-A ports · 5 V DC 2 A shared |
| Cut-Out Size (required) | 220 mm L × 110 mm W |
| Visible Bezel Size | 265 mm L × 120 mm W |
| Body Depth* | ≈ 65 mm below mounting surface |
| Power-Cord Length | 1.4 m captive lead with moulded AU plug |
| Finish / Colour | Satin-Silver bezel · Brushed-steel pop-up lid |
| Compliance / Safety | ERAC Level-3; AS/NZS 60950.1 & 61558.2.16 certified |
| Shipping Weight | ≈ 1.45 kg (boxed) |
*Depth is measured from the underside of the mounting flange to the lowest point of the enclosure and is approximate – allow clearance for wiring.
How To
How To
Step-by-Step Installation Guide
Important: This module is a plug-and-play retrofit. Because you are
only plugging into a standard wall outlet, a licensed electrician is generally
not required. If unsure, seek professional advice.
-
Unplug & Prepare
Switch the recliner or lounge off at the wall and unplug its transformer.
Clear a work area large enough to tip the furniture without obstruction.
Lay a moving blanket or thick towel on the floor to protect upholstery. -
Safe Lifting & Access
Recruit a helper—powered lounges can exceed 70 kg. Lift with your legs,
keep the load close, and avoid twisting. Tip the furniture onto its back or
side so the console top is horizontal and easy to reach. -
Take “Before” Photos
In good light, photograph
• the existing charging hub or blank plate
• all screws / spring clips underneath
• cable routing and strain-relief points
These images make re-assembly and troubleshooting much easier. -
Remove the Old Unit / Blank
Open the console lid and locate the four corner screws (or spring latches).
Support the unit with one hand while removing fasteners with the other.
Slide the module upward and disconnect any plugs. Free the captive lead
from cable ties or clips. -
Confirm Cut-Out Size
Measure the aperture—it must be 220 mm × 110 mm (±2 mm).
• If smaller, carefully enlarge with a jigsaw.
• If larger, screw a timber spacer frame so the new unit is fully supported. -
Seat the New Charger
Lower the MLCZ005-13 into the hole; its bezel (265 mm × 120 mm) should sit
flush. Engage the spring clips or re-use the four screws—snug, not overtight. -
Route the Power Lead
Feed the 1.4 m mains cord through the console cavity, following the
original path. Keep clear of sharp edges and moving mechanism arms.
Secure with the supplied clip or a zip-tie to prevent tug-strain. -
Restore Power & Test
Stand the lounge upright using the same safe-lifting technique.
Plug the charger’s lead into a wall socket (or recliner power strip) and
reconnect the recliner transformer. Open the lid, test both 240 V sockets
with a lamp and charge a phone from each USB port. -
Final Checks
Ensure the lid closes flush, wiring is tidy and no cables are pinched
beneath the console. Store removed screws and your “before” photos for
future reference.
Total time ≈ 15 minutes with two people. Enjoy convenient charging
right at your seat and the satisfaction of a safe DIY upgrade. If any step is
unclear, send us your photos—our support team is ready to help.
Reviews (0)
Thank you for making an effort to leave a reivew but to protect against spam we only accept reviews from verified owners. Please proceed to login using the same email address you used when ordering the product.
Customer Login
- There are no reviews yet.
FAQs
FAQs
Will the MLCZ005-13 fit the cut-out already in my lounge console?
Measure the opening after you remove the old unit or blank plate. If it is ≈ 220 mm × 110 mm (give or take 2 mm) the charger will drop straight in and the 265 mm × 120 mm bezel will sit flush. A larger cut-out can be packed with a timber frame; a smaller one must be carefully enlarged.
Does this replace the 29 V transformer that powers my recliner motors?
No. This module only provides household AC outlets plus 5 V USB charging for phones, tablets, laptops, lamps, etc. Your recliner’s motors still need their separate 29 V power supply. Both can share the same wall socket via a power board if required.
How powerful are the USB ports—will they fast-charge my phone?
Each USB-A port delivers 5 V DC, up to 2 A shared (10 W max). That is fast enough for most phones, AirPods and controllers, but it is not a high-voltage Quick-Charge or USB-C PD port. For the fastest charging, plug your device’s own wall charger into one of the 240 V sockets.
Do I need an electrician or special tools to install it?
No electrician is needed because you’re not altering fixed wiring—just plugging into an ordinary 3-pin outlet. You’ll need only a Phillips screwdriver to remove the old module and tighten the four retaining screws (or release/engage spring clips). If you must enlarge the hole, a jigsaw and eye/ear protection are recommended.
Which sofa brands use this charger, and can I retrofit it into others?
The MLCZ005 family is factory-fitted in many Synargy Smart Comfort, Amart, and Harvey Norman theatre lounges. Because the unit simply needs the correct cut-out and a nearby power point, it can be retro-fitted to almost any recliner console, desk or RV cabinetry that meets the size requirement.
